DOOR SEAL OVEN ELECTROLUX/ZANUSSI 1475x660 mm

DOOR SEAL OVEN ELECTROLUX/ZANUSSI

General Info:
in the silicone elastomer
profile dimensions 29,3x11,8 mm
COLOR BLACK

For: ZANUSSI convection Oven FCZ202GKZA (236805), FCZ202GTL1 (237725), FCZ202GTZA (237805), FCZ202GBL1 (238725), FCZ202GBZA (238805), FCZ202GCZA (239805), AOS202EABU (260089), AOS202EAFU (260094), AOS202GAEU (260099), AOS202GAAU (260152), AOS202GAPQ , RDR202GAG (647545), RDR202GBG (648545), FCZ202GBGE (648715)
ZANUSSI convection Oven electric FCZ202EKA (236205), FCZ202EAA (237005), FCZ202ETA (237205), FCZ202EBA (238005), FCZ202EBA2 (238205), FCZ202ECA (239005), FCZ202ECA2 (239205), AOS202EA2N (260502), AOS202EB2N (260503), AOS202EA (260518), AOS202EB (260519), AOS202EAAQ (260608), AOS202EBAQ (260609), AOS202EANQ (260618), AOS202EBNQ (260619), AOS202EKA1 (266205), AOS202ETA1 (267205), AOS202EBA2 (268205), AOS202ECA2 (269205)
ZANUSSI convection Oven gas FCZ202GKG (236705), FCZ202GKD (236715), FCZ202GAG (237505), FCZ202GAD (237515), FCZ202GTG (237705), FCZ202GTD (237715), FCZ202GBG (238505), FCZ202GBD (238515), FCZ202GBG2 (238705), FCZ202GBD2 (238715), F AOS202GBG2 (268705), AOS202GBD2 (268715), AOS202GCG2 (269705), AOS202GCD2 (269715), FCZ202GKGN (646705), EJN202GAG (647505), EJN202GAD (647515), FCZ202GTGN (647705), EJN202GBG (648505), EJN202GBD (648515), FCZ202GBGN (648705), EJN202GCG (649505), EJN202GCD (649515), RDR202GCG (649545)

Adaptability:
MANUFACTURER CODE
0C1195 ALPENINOX
0C1889 ALPENINOX
0C1195 ELECTROLUX PROFESSIONAL
0C1889 ELECTROLUX PROFESSIONAL
0C1195 ZANUSSI
0C1889 ZANUSSI

In this category you can find all the models of gaskets for oven door ELECTROLUX/ZANUSSI for professional kitchens

Instructions and tips for the replacement/installation of the seals:

1) Remove the old seal from its seat

2) thoroughly Clean all of the debris and dirt both from the throat-snap-fit on the bearing surface with specific detergents

3) In the event of difficulties in inserting the gasket in the joint spraying/wetting with liquid soap

4) Mount the gasket starting from the corners in the sequence: (as in photo 1)

- First mount the 4 corners A-A1, B-B1

- Then the center between the points C-C1

- Now push the rest of the gasket starting from the center to the points C-C1 and D-D1

*CAUTION: if the seal has a hole, air vent, the side with the hole must be mounted in the bottom (as in photo 2)

*IMPORTANT: CHECK DOOR SEAL

- If the gasket is mounted correctly, steam should not result in a loss of steam

- In the "combi steam" to 300C, the door must be closed properly. Otherwise an adjustment is needed of the door.

Care and repeated cleaning during the day, greatly extend the life of the seals.