DOOR GASKET OVEN FAGOR 775x700 mm

DOOR SEAL OVEN-FAGOR

General Info:
seal mezzobordo
in the silicone elastomer
profile dimensions 22x17,4 mm
COLOR BLACK

For: FAGOR convection Oven electric HME-10-11, HME-10-21, HME-2-10-11, HME-6-11, HMI 10, HMI-10-11, HMI-10-11UL, HMI-10-21, HMI-10-21UL, HMI-2.10, HMI-2-10-11, HMI 6, HMI-6-11, HMI-6-11UL, HMM-10, HMM-10-11, HMM-10-11UL, HMM-10-21, HMM-10-21UL, HMM-10UL, HMM-2.10, HMM-2-10-11, HMM-6, HMM-6-11, HMM-6-11UL, HMM-6UL, HMP-10-11, HMP-10-21, HMP-2-10-11, HMP-6-11, MFHMI-6, MFHMI-6-11, MFHMM-10, MFHMM-6-11, THCV-10-21P, THCV-2-10-11P, THCV-6-11, STEAD-10-21, VECE-2-10-11, STEAD-6-11, VECM-10, VECM-10-11, VECM-10-21, VECM-2.10, VECM-2-10-11, VECM-6, VECM-6-11, VECP-2-10-11, VECP-6-11, VEI-10, VEI-10-21, VEI-2.10, VEI-2-10-11, VEI-6, VEI-6-11
FAGOR convection Oven gas (HCG) 1.10-11, HCG-10-11, HCG-10-21, HCG-2.10-11, HCG-6-11, HGC-10, HGC-2.10, HGC-6, HVG-1011, HVG-10-11, HVG-10-11UL, HVG-1021, HVG-10-21, HVG-10-21UL, HVG-10UL, HVG-2.10, HVG-2.10-11, MFHMI-10-11, MFHMI-10-21, MFHMM-10-11, MFHMM-10-21, MFHVG-10, MFHVG-10-21, VCG-10, VCG-10-11, VCG-10-21, VCG-2.10, VCG-2.10-11, THE VCG-6 AND VCG-6-11, VGT-10, VGT-10-21
FAGOR Oven sottocucina electric HMI-1011, HMI-1021, HMI-611, HMM-1011, HMM-1021, HMM-611

Adaptability:
MANUFACTURER CODE
R680500000 FAGOR
12017439 FAGOR

Sales and spare Parts gaskets for oven door convection electric convection gas FAGOR

Instructions and tips for the replacement/installation of the seals:

1) Remove the old seal from its seat

2) thoroughly Clean all of the debris and dirt both from the throat-snap-fit on the bearing surface with specific detergents

3) In the event of difficulties in inserting the gasket in the joint spraying/wetting with liquid soap

4) Mount the gasket starting from the corners in the sequence: (as in photo 1)

- First mount the 4 corners A-A1, B-B1

- Then the center between the points C-C1

- Now push the rest of the gasket starting from the center to the points C-C1 and D-D1

*CAUTION: if the seal has a hole, air vent, the side with the hole must be mounted in the bottom (as in photo 2)

*IMPORTANT: CHECK DOOR SEAL

- If the gasket is mounted correctly, steam should not result in a loss of steam

- In the "combi steam" to 300C, the door must be closed properly. Otherwise an adjustment is needed of the door.

Care and repeated cleaning during the day, greatly extend the life of the seals.